Hands rolling a Tumbler Rolling Knife Sharpener along a chef's knife held on its 15° magnetic angle block on a wooden kitchen counter

How Often Should You Sharpen Your Knives? What Zwilling and Shun Say

Hands rolling a Tumbler Rolling Knife Sharpener along a chef's knife held on its 15° magnetic angle block on a wooden kitchen counter

Most home cooks need to sharpen their kitchen knives only one to three times a year, and hone them far more often, anywhere from once a week to every day. Honing realigns the edge you have; sharpening grinds away metal to make a new one. So sharpen when honing stops working, not because a date came around.

That range comes from two knife makers. Shun puts sharpening at about once a year for many home cooks, and Zwilling's Bernard Janssen says two to three times a year unless you cook professionally or use your knives all day. Below, we sort their advice by how you cook and add a routine for the Tumbler Rolling Knife Sharpener. New to rolling sharpeners? Our complete rolling sharpener walkthrough covers the technique from setup to finish.

How often to hone and sharpen, by how you cook

Hone on habit, sharpen on need: the harder a knife works, the more often it needs both. Neither maker sorts cooks into these four groups, so the rows are our reading of Shun's and Zwilling's guidance. Where the two differ, we give the busier kitchen the higher figure, and where neither gives a number, the row says so.

How you cook Hone Sharpen On a Tumbler
Occasional cook (a few meals a week) About once a week (Shun) About once a year (Shun) About 6 passes per side on the EdgeBoost honing disc each time you hone
Daily home cook A few times a week (Zwilling's Janssen) Two to three times a year (Janssen) Hone on the EdgeBoost disc; once you're on a schedule, sharpening becomes a short touch-up (times in step 3 below)
Heavy home use or batch cooking As needed, up to every day (Shun) More often, whenever honing stops bringing the edge back (Shun) Hone before each session; switch to the diamond disc when honing no longer helps
Professional kitchen Multiple times a day (Janssen) More often than a home cook; neither maker gives a number Frequent honing, short regular touch-ups rather than long sessions

A knife that hasn't been sharpened in a long time sits outside this table. Start it with a full sharpening (step 3 of the routine below), then put it on the schedule that matches your cooking.

What do Shun and Zwilling say?

Both knife makers give the same rule in different words: hone often, and sharpen only when honing can no longer restore the edge.

Shun's care page boils it down to "hone for maintenance, sharpen for restoration." On honing, it allows a wide range: "Some cooks hone once a week, while others hone every day," depending on how much the knife is used. On sharpening, it says, "For many home cooks, sharpening about once a year is often enough," with heavier users needing it more often (Shun Cutlery).

Zwilling's own care guide says knives "should be honed regularly and sharpened occasionally," and names the trigger for the second job: "If the cutting edge can no longer be renewed by honing, it must be reground to bring on a new edge" (Zwilling). Speaking to Simply Recipes, Zwilling's Bernard Janssen put the sharpening interval at two to three times a year for most cooks and recommended "honing a few times a week" for a knife in daily use (Simply Recipes via AOL).

The two numbers differ, and neither maker sets a date on the calendar. Both tell you to watch the edge. If you want the detail on what each process does to the steel, our explainer on what honing and sharpening each do to an edge goes deeper.

Signs it's time to sharpen, not just hone

A knife needs sharpening when a few honing passes no longer bring back clean cuts. GearJunkie's sharpening guide, written for pocket knives, gives three checks you can run on a kitchen knife too (GearJunkie):

  • Paper. Slice a sheet of paper using the whole edge. If the blade snags or rips the sheet anywhere, GearJunkie's call is to sharpen, or at least hone.
  • Light. Hold the edge toward a light. "If a part along the blade reflects back the light, that part is rounded and will need to be sharpened."
  • Feel. If the knife is "not working as smoothly as you're used to," it probably needs sharpening.

Hone first, then run the paper check again. Shun's rule for the next step is short: "If the knife still feels dull after honing," then "it is time to sharpen." A full set of dullness tests has its own guide on the way.

In this Tumbler reel, a tan angle block goes down on an end-grain board, the roller's spiral honing face is shown up close, a blade is laid across a Tumbler leather strop, and the clip ends with cut paper strips and a chef's knife over a tall stack of tortillas.

A simple routine with a rolling sharpener

On a rolling sharpener, the schedule above becomes four short habits.

  1. Hone on your schedule. Flip the roller to its EdgeBoost honing disc, steel on the Tumbler Original and ceramic on the Tumbler Pro, and make about 6 passes per side. That's plenty between sharpenings.
  2. Test, then decide. Run the paper check. A clean slice means you're done. If the paper still catches after honing, move on to step 3.
  3. Sharpen at the knife's angle. Set the blade on the magnetic holder. The Tumbler Original comes with a holder that has a 15° side and a 20° side, and the Knife Holder Pro adds 10° and 25°. Roll the diamond disc with light pressure along the whole edge, from the heel all the way to the tip, and check for a burr with a fingernail as the official Tumbler setup steps describe. Budget about 2 to 12 minutes for a knife that's dull or hasn't seen a sharpener in a long while; where it lands in that range depends on how worn the edge is and how long it's been since its last session. Once you sharpen on a schedule, a touch-up takes about 60 seconds. A guide to sharpening time is coming.
  4. Hone again, then strop if you like. A few passes on the honing disc settle the fresh edge. The Tumbler Companion Strop is, in the store's words, "the optional final touch, not a replacement," and our guide to stropping a kitchen knife shows the stroke.

Both models follow the same routine. The main difference for upkeep is the honing disc: the Pro's ceramic surface is coarser than the Original's steel, and the Pro's discs can be swapped. You can see the Original and Pro compared for the rest.

Knife sharpening frequency questions

Can you over-sharpen a knife?

Yes. Every sharpening takes metal off, so sharpening more often than the knife needs wears the blade down sooner. Shun is direct about it: "Because sharpening removes metal from the blade, it should be done only when the knife truly needs it." Honing is the habit you can repeat freely, since Shun says "it does not remove metal." Nobody can promise a set number of sharpenings per blade, so test first, sharpen only on a fail, and roll with "a light amount of pressure," as Tumbler's instructions put it. Our post on common knife sharpening myths covers more of the misunderstandings, and our guide to whether a knife sharpener can ruin a knife shows how to spot edge damage.

How often do professional chefs sharpen their knives?

More often than home cooks, though neither knife maker gives a number. Shun says professional cooks and other heavy users "will likely need to sharpen more often," and Janssen notes that "A professional will hone multiple times a day." The professional pattern is constant honing, with sharpening whenever honing stops restoring the edge.

Should you sharpen a brand-new knife?

Test it first. If a new knife slices paper cleanly along the whole edge, there's nothing to sharpen yet, so start the honing habit instead. Because sharpening removes metal, sharpening a knife that already passes the test spends steel for no gain.

Sources

Written by Team Tumbler.